Features
- 【Highly efficient, quick heating】
Gas heating efficiency has been greatly improved thanks to the specially designed sheathed heating element. - 【Greatly reduced heater surface temperature】
The heater’s special internal structure has substantially reduced the surface temperature of the heater’s tubular body, eliminating the need for heat insulating material or cooling. - 【Energy saving】
The new heater consumes about 15% less electricity.(than our previous models).
Types
MCA-500E
Specification
All products listed are available in different voltages.
| Rating | 200V 500W |
|---|---|
| Insulation resistance | DC500V 5MΩ or above |
| Dielectric strength | AC400V for one minute,current detection 10mA |
| Maximum operating temperature | 500℃ (at built-in thermocouple) |
| Temperature at outlet tip | See the temperature characteristics graph. |
| Flow rate | 20Nℓ/min ～100Nℓ/min |
| Gas pressure | Up to 0.3MPa (3kgf/cm2) |
| Material | Stainless steel (tubular body, flexible heater,sheathed thermocouple) |
| Tubular body dimensions | φ48.6×156mm (L) |
| Heated substance | Air, inert gas, etc. |
| Heater lead wire | L500mm cut-off |
| Thermocouple | Grounded K Type Compensation Lead Wire L2000mm (M4, Y terminal) |
* Please contact us for any requests for customized heaters.
Temperature characteristics
Flow rate-Outlet tip temperature
MCA-1000E
Specification
All products listed are available in different voltages.
| Rating | 200V 1000W |
|---|---|
| Insulation resistance | DC500V 5MΩ or above |
| Dielectric strength | AC400V for one minute,current detection 10mA |
| Maximum operating temperature | 500℃ (at built-in thermocouple) |
| Temperature at outlet tip | See the temperature characteristics graph. |
| Flow rate | 20Nℓ/min ～100Nℓ/min |
| Gas pressure | Up to 0.3MPa (3kgf/cm2) |
| Material | Stainless steel (tubular body, flexible heater,sheathed thermocouple) |
| Tubular body dimensions | φ60.5×291.5mm (L, the flange inclusive) |
| Heated substance | Air, inert gas, etc. |
| Heater lead wire | L500mm cut-off |
| Thermocouple | Grounded K Type Compensation Lead Wire L2000mm (M4, Y terminal) |
* Please contact us for any requests for customized heaters.
Temperature characteristics
Flow rate-Outlet tip temperature
MCA-1500E
Specification
All products listed are available in different voltages.
| Rating | 200V 1500W |
|---|---|
| Insulation resistance | DC500V 5MΩ or above |
| Dielectric strength | AC400V for one minute,current detection 10mA |
| Maximum operating temperature | 500℃ (at built-in thermocouple) |
| Temperature at outlet tip | See the temperature characteristics graph. |
| Flow rate | 20Nℓ/min ～100Nℓ/min |
| Gas pressure | Up to 0.3MPa (3kgf/cm2) |
| Material | Stainless steel (tubular body, flexible heater,sheathed thermocouple) |
| Tubular body dimensions | φ60.5×291.5mm (L, the flange inclusive) |
| Heated substance | Air, inert gas, etc. |
| Heater lead wire | L500mm cut-off |
| Thermocouple | Grounded K Type Compensation Lead Wire L2000mm (M4, Y terminal) |
* Please contact us for any requests for customized heaters.
Temperature characteristics
Flow rate-Outlet tip temperature
Precautions when using this product
- This product is for industrial use only.
- Before turning on the heater, ensure that the gas is being supplied. aboutt 15% lless
- Ensure that the gas being supplied is at ambient temperature.
- Use the heater with the built-in thermocouple connected to a temperature control device and the temperature maintained at or below 500℃.
- To stop the heater, first turn off the heater while the gas is still being supplied.
Then, after ensuring that the temperature of the built-in thermocouple has dropped to or below 50℃, shut off the gas supply.